SURECOM SA-160 LCD Display 0.5-60MHz Color Graphic Antenna Analyzer BNC Connector for Two Way Radio SA160 Antenna Testing Meter
Â
Surecom SA-160 antenna analyzers designed for testing, checking, tuning or repairing antennas and antenna feed lines.
Mainly, these are S.W.R. (Standing Wave Ratio) and impedance measurement instruments (vector impedance analyzers).
Easy-to use measurement modes. make SURECOM attractive for professionals and hobbyists. It is quite important that graphical display of various parameters over a wide frequency range is a key feature of these analyzers which significantly reduces the time required to adjust an antenna.
Â
Main Features:
     2.2 ” precision LCD screen,High-lumen LCD brightness, easy to read in direct sunlight
     Heavy duty Aluminum enclosure,strong anti-interference ability.
     Very compact and convenient for field use
     Built-in rechargeable Li-ion battery
     Full Band control (No need select Band )
     Easy setup, only four control buttons with convenient on-screen soft menus
     Constant Battery Status Indicator and Auto Shut-off
     Built-in timer shows elapsed time when unit is turned on
     High efficiency IC, low power consumption, the longest working hours
     More choice measurement frequency Span .
     One botton quick scan mode HF1,HF2,HF3 or 3 band by full screen.
     Auto marker the Best s.w.r. level referenceÂ
Â
Specifications:
Model No. SA-160
Frequency Range: 0.5-60MHz
Connector: BNCÂ (50 OHM)
RF Output Power: 1-1.5V(5 – 10dB)
Frequency Step: 0.1/1/10/100/1000KHz
V.S.W.R. Range: 1.00-19.99
ZRX Range: 0-99.9
Build-in Battery : 3.7V 900mah ,Li-ion 14500
Voltage input : DC5V> 500mAÂ
Frequency stability: <0.5PPM
Span width: 0.54MHz/1.35MHz/2.7MHz/13.5MHz/27MHz/62.1
Charger indicator: Two-color LED Hidden (when not charging) there are three instructions state:Â
1, charging (red) ;
2, charging is completed (green)Â
3, Battery fault (flashing)
Charger Plug: Standard Micro USB connector
Size: 70 x 120 x 25 mm
Colour Display: TFT LCD 320 x 240 pixels
Weight:Â 172g
Â
Power Management
Power Source: Size 14500 of Lithium battery.
Charge Controller: Smart charger, LED charging-status indicator
Voltage Monitor: On-screen DVM, plus battery condition icon
Power Savers: Auto-off timer, Auto Run/Stop RFgenerator control
Interface
RF Connector: BNC -femaleÂ
 Charge Connector: Micro-USB
Control and Display
SPAN: 0.27/0.54/1.35/2.7/5.4/13.5/27/62.1MHz
LCD: 2.2 inch high-output color TFT
Function Keys : 4 botton, with on-screen (soft-menu) identifiers
Tuning: Rotary encoder with press-in tuning-step selection
Weight and Dimensions
Case: Aluminum metalÂ
Size: 7 cm wide x12cm height H x 2.5 cmÂ
Weight: 6.1 oz (0.172 kg)
Â
Turn on and off the power
   Turn on the power, Press and hold White botton when the dot disappearÂ
    from left up angle ,. top Menu appeared on the screen. Â
   Turn off the power, You have 2 method :
    a)On Top Menu page ,Press and hold the White [F1 ] botton at 5 second .
    b)On Top Menu page , Rotary encoder on “Power off”, Press the [F2 Enter]
Â
1.1Function Select
   You can turn the knob select you want function and press [F2.Enter] botton .
Â
2.0 ANTENNA TEST EXAMPLESÂ by Scan mode
2.1[Scan] mode page
   In the Top Menu screen: Rotary encoder on “Scan”, Press the [F2 Enter],   to frequency mode measurement button, enter Scan (scan mode) screen.
 Press [F.2 scan ],button to start the scan operation. During scanning, in order to ensure measurement accuracy, each frequency will stay for short while. one scanning cycle will take about 1-2 seconds.    Once SCAN is done, it will enter ”Present” mode (result) screenÂ
 You have results on the screen : Show the SWR curve only (because default setting SWR curve only , Zx curve, Rs curve Disable) You can Enable other curve on the screen: On Top Menu page,Â
   Rotary encoder on “Zx”, Press the [F2 Enter] to enable . Other cure will Disable when Power Off , If want enable in the future, Rotary encoder on “Save”, Press the [F2 Enter] to save setting .
Â
2.2 1. lnfull (default SCAN range 0.56MHz -59.9MHz,span 62.1MHz )
     * Long press to [SCAN ]and press [F3 UPDn] select “1.Infull”,and then release the scan botton.
    2.lrnMk=(Learn marker move to center frequency)
     * Long press to [SCAN ]and press [F3 UPDn] select “2.IrnMk”,and then release the scan botton.
2.3Â [View]Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â
   view the scan frequency point on the curve on each scan of the specific parameters of the measurement results.
  – Press the [F3.View ] button to start the view operation mode. rotary encoder ,the white triangle curve marker is move
  – Dot scale will display on screen, Press bottom change the Dot scale,You have 3 options of Dot scale mode for choose,[Dot =x1] [Dot=x10][Dot= x25] . (230KHz,2.3MHz,5.8MHz)
   SWR Full scale will display on screen,Press bottom change the graphically plot SWR,You have 3 options scale mode for choose, [SWR=x2 ][SWR= x 0.5][SWR=x1] .(1-9,1-19,1-4.5)
Â
2.4[ Quick 1] start Scan mode:
   Quick view the scan frequency point on the curve on each scanÂ
    Press the button [Quick   1 ] to start the Quick 1 operation mode .You have 3 options scan mode for choose .
   1)Press the button [F1. Scan 1 ]  0.5 to 27.3MHz can of the specific parameters of the measurement results.
   2)Press the button [F2. Scan 2 ] 16.6 to 43.4MHz can of the specific parameters of the measurement results.
   3)Press the button[F3. Scan 3 ] 33.6 to 60.0MHz can of the specific parameters of the measurement results.
Â
PACKAGE CONTAIN:
1 x SURECOM SA160 (ENGLISH VERSION) Colour Graphic Antenna AnalyzerÂ
1 x English User”s Manual
1 x Mirco Usb Charger Cable
Reviews
There are no reviews yet.